Recent Activity
Activity stream for all registered members at OpenBuilds.
-
KEN MACDONALD replied to the thread SPARK CONCEPTS XPRO V3 PROBLEM.
That is set at 199.900, which I think is correct
Jun 5, 2024 at 12:31 PM -
KEN MACDONALD replied to the thread SPARK CONCEPTS XPRO V3 PROBLEM.
You are correct in that $100 = 8.00 instead of 26.67. All the others appear to be correct. I cut one piece ok, but now when I set it and...
Jun 5, 2024 at 12:08 PM -
Mark Carew liked Rick 2.0's post in the thread OpenBuilds Table Series.
4x4s and 2x8s would probably be your best bet.
Jun 5, 2024 at 10:25 AM -
Mark Carew liked Peter Van Der Walt's post in the thread OpenBuilds Table Series.
How to calculate V-Slot® deflection Might be a bit much - its M5 fasteners and 20x60/40x40 extrusions
Jun 5, 2024 at 10:25 AM -
Caitlyn liked Peter Van Der Walt's post in the thread BBx32 Out of Box issues.
Tool Enable pin > $1.50 relay module > Switch the Enable on the Driver [ATTACH] Could still use Relay 1 (just Set $16 correctly, and...
Jun 5, 2024 at 9:18 AM
-
Caitlyn replied to the thread BBx32 Out of Box issues.
Thanks!
Jun 5, 2024 at 9:17 AM -
Rick 2.0 replied to the thread Workbee Lead 1000x1000 Wheel Clearance too tight.
If you’re getting 8.6mm it sounds like your bearings are not properly seated. This is one of those items that is very consistent. A...
Jun 5, 2024 at 9:14 AM -
Caitlyn replied to the thread BBx32 Out of Box issues.
The starter spindle I bought was this:Amazon.com (48VDC, Brushless.) I was going to have the SSR switch the AC hot line to the 48VDC...
Jun 5, 2024 at 9:08 AM -
KEN MACDONALD replied to the thread SPARK CONCEPTS XPRO V3 PROBLEM.
Ok thank you
Jun 5, 2024 at 9:08 AM -
KEN MACDONALD replied to the thread SPARK CONCEPTS XPRO V3 PROBLEM.
Ok thankyou I'll take a look, but it's quite a large difference. I've just tried to centerline cut a letter H which measures 50mm square...
Jun 5, 2024 at 9:04 AM -
Caitlyn replied to the thread BBx32 Out of Box issues.
I was thinking some form of safety light (like the cheap red/yellow/green ones) to indicate machine is running / stopped / etc. (So...
Jun 5, 2024 at 8:42 AM -
KEN MACDONALD posted a new thread.
SPARK CONCEPTS XPRO V3 PROBLEM
Hi I've just tried to do some cutting on my Ooznest OX cnc, but it seems to have developed a fault. I suspect its the control board...
Forum: Controller Boards
Jun 5, 2024 at 8:38 AM -
mleaming liked cnc-trucker's post in the thread Standalone Torch Height Controller for CNC Plasma Cutting.
Jeramiah, in one of your posts in this forum topic, you stated that if anyone could integrate your THC into a GRBL machine, you would...
Jun 5, 2024 at 8:12 AM -
Caitlyn replied to the thread BBx32 Out of Box issues.
v1.2 is printed on the PCBs. I have two of these x32s, bought years ago, and finally putting them to use. Both are exhibiting the same...
Jun 5, 2024 at 8:09 AM -
Rick 2.0 replied to the thread OpenBuilds Table Series.
4x4s and 2x8s would probably be your best bet.
Jun 4, 2024 at 9:14 PM